Jump to content

laireV

Moderators
  • Content Count

    338
  • Joined

  • Last visited

  • Days Won

    22

Everything posted by laireV

  1. Implement the following setting below: *For 2.4GHz Change the Channel HT mode to 20MHz only Use non-overlapping channel: 1,6, or 11 (note that each access point should have a unique channel) Use WPA2-PSK/AES only for the wireless security Set the TX power to 18dBm *For 5GHz Change the Channel HT mode to 40MHz only Use non-overlapping channel: 44, 60, 108, 124, 132, 157 Use WPA2-PSK/AES only for the wireless security Set the TX power to 23dBm
  2. See article posted on EnGenius Help Center: https://helpcenter.engeniustech.com/hc/en-us/articles/115006488968-Why-can-t-I-factory-reset-the-ENS1750-via-hardware-reset-button-
  3. This sounds interesting. Could you try powering down the unit for 10 seconds then power it back on after 10 seconds. Press the vol+ button to increase and vol- to decrease the volume of the base ringer. Do this while base is on idle (not in use).
  4. How did you configure the ENH700EXT? What channel you use per band and per access point?
  5. Your only calculating the number of cameras per link. Keep in mind that your setup is point to mulitpoint. This means, the number of cameras and bandwidth doubles. See EnStation5 and EnStationAC calculation below:
  6. The Freestyl1 base station has a dial pad. You may use the up and down button from the base to adjust the volume ringer of the base station.
  7. If you are looking for higher capacity, you may check the EnStationAC
  8. At least 30ft away from the root bridge. Based on the current cameras settings that you have, you can only transmit up to 10 cameras back in to the ENS500.
  9. Thought it was an ECB1750 as stated on your subject. Anyhow, there shouldn't be any issues with the new firmware release.
  10. I never had any issues with the latest firmware build. Just curious, did you factory reset the unit after the firmware update? There are added feature, functions, bugs fixes, and some device enhancement on the new firmware release which may not be compatible with the current configuration of your EAP1750H.
  11. 15 cameras at 720? Perhaps you may want to try reducing the number of cameras per access point. I suspect the ENS500 could not handle the traffic. You can also try adding another root bridge and create another Point to multipoint bridge.
  12. Couldn't see what would cause the band steering not to work. Band Steering focuses on dual band client devices. It steer them only to connect to the 5GHz radio band. If both the 2.4GHz and 5GHz band has the same wireless SSID and security parameter, this should work flawlessly. With the current settings that you have, it will help to get a stable to connection if you change the wireless HT mode of your 2.4GHz band to 20MHz only and the encryption to WPA2-PSK/AES only.
  13. How many cameras connected per ENH500? What are the specs of the cameras (FPS, RES)? ENS500 may not be able to handle too much traffic and that is the reason why it shows the connection is down. You may probably need to create 2 root bridges to evenly distribute bandwidth.
  14. Point taken. It should be Restore to Factory Settings to restore factory standard settings instead. Some manual revisions should be made not only for this particular model. Apologies for the confusion.
  15. There are 2 options on the Reset section. You can Restore to Factory Default Settings or Restore to User Default
  16. Good catch @Milo Van. @ThatSeattleGuy, hope this suffices your requirement.
  17. Did you send an email to [email protected]? They mask ask for some additional information. How you telnet the ENH500, for instance. Software you use to telnet it. It would be very helpful for the engineering to find the root cause of the issue it you could provide as many information as possible.
  18. Check out the link on the EnGenius Help Center: https://helpcenter.engeniustech.com/hc/en-us/articles/235458488-White-Paper-Using-VLANs-with-EnGenius-APs-and-Switches
  19. Check out the link on the EnGenius Help Center: https://helpcenter.engeniustech.com/hc/en-us/articles/115006361768-Configuring-a-Mesh-Network-with-EnGenius-Neutron-EWS-Controller-
  20. Bob, Are you looking for the firmware of the EAP1750H? See link below: https://www.engeniustech.com/engenius-products/indoor-wireless-ceiling-ap-eap1750h/
  21. You're most welcome Dude!
  22. Check out the link on the EnGenius Help Center: https://helpcenter.engeniustech.com/hc/en-us/articles/115005869648-Installing-and-setting-up-ezMaster-on-Virtual-Machine
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.