Jump to content
Sign in to follow this  
  • entries
    5
  • comments
    0
  • views
    406

About this blog

Issue Description

 Change the running OptiX OSN 3500 from a main subrack into an extended subrack. Mount the extended subrack to a newly created OptiX OSN 3500. Query the physical slots of the extended subrack. It is found that the boards in the extended subrack fail to be displayed and that the tributary boards in the extended subrack are displayed as off-service on the T2000. 

Alarm Information

Null

Handling Process

1.Check the connection between the main subrack and the extended subrack. It is found that the connection is normal. 
2.Perform warm reset on the SCC board and the AUX boards in the main subrack and in the extended subrack. It is found that the problem persists. 
3.Remove the off-service boards and then insert the boards back to force the boards to perform cold reset. Then, the boards obtain the new slot IDs. The problem is solved. 
 

Root Cause

The possible causes are as follows: 

1.The connection between the main subrack and the extended subrack is faulty. 
2.The SCC board in the main subrack and the AUX boards in the main subrack and in the extended subrack are faulty. 
3.The tributary boards in the extended subrack are not reset and thus the correct slot IDs cannot be obtained. 
 

Suggestions

The following part considers the UXCSB as the cross-connect board of the main subrack and describes the precautions for the connection between the main subrack and the extended subrack.

· Cable connection between the UXCSB and the XCE: The EXA and EXB ports on the UXCSB board in slot 9 are connected to the EXA ports on the XCE board in slots 59 and 60. The EXA and EXB ports on the UXCSB board in slot 10 are connected to the EXB ports on the XCE board in slots 59 and 60. See Figure 1.

· The EXT port on the AUX board in the main subrack is connected to the EXT port on the AUX board in the extended subrack. See Figure 1.

· Cover the J9 jumper on the AUX board in the main subrack with the jumper cap and maintain the J9 jumper on the AUX board in the extended subrack uncapped.

· Do as follows to reconstruct a running main subrack into an extended subrack:

00001. Remove the SCC board, line board, and certain unused tributary boards.

00002. Connect the EXT ports on the two AUX boards and remove the J9 jumper on the AUX board in the extended subrack.

00003. Remove the two cross-connect boards.

00004. Insert two XCE boards instead and connect the two XCE boards to the UXCSB boards in the new main subrack.

After the two cross-connect boards are removed, the extended subrack has no cross-connections. Hence, the tributary boards in the extended subrack are automatically reset. After the J9 jumper is removed from the AUX board, the tributary boards can obtain the new slot IDs (that is, the original ID plus 50). After performing the operations, you need not remove the tributary boards and then insert the boards back again after the configuration.

Entries in this blog

 

When the ODUk SPRing Protection Switching Is Performed by Running External Commands, If the Tributary Board Is Not in Position, the Switching May Fail

Issue Description When the ODUk SPRing protection switching is performed by running external commands, if the tributary board is not in position, the switching may fail.  Alarm Information Null   Handling Process If the tributary board for the westward or eastward services of the ODUk SPRing protection is not in position, performing the switching by running external commands is nonsense. If you really intend to perform the switching by running external commands, you must

zara

zara

 

VCAT_LOA was appearing on N2EFS4 board due to the inconsistent of SNCP state

Issue Description There is one Ethernet service between two NEs (OSN7500 having software version of 5.21.18.53). Service type is Ethernet Line Service of 2Mbps. Moreover there is configured SNCP between two different lines on SDH layer to protect 2Mbps Ethernet Line Service in case of dual fiber break. The SNCP service is configured NON-Revertive for beow topology. NE1-NE2-NE3-NE4 (Working path) NE1-NE5-NE6-NE4 (Protection path)   Alarm Information ALM_GFP_dLFD VCAT_LOA VCAT_L

zara

zara

 

How to resplve The Device Does Not Respond to Input from the Keyboard

If you huawei switch S5720 Not Respond to Input from the Keyboard,what should you do, then let me tell you. Fault Description The command line interface of the device suddenly does not respond to input from the keyboard. Possible Cause The device is processing other services and the high CPU usage results in no response to the input from the keyboard. Another user restarts the device or the devic

zara

zara

 

EPL service does not work after configuration

Issue Description There are two OSN 3500, we config one EPL service with exterior port attribute is Hybrid, but we can not ping successfully with no VLAN message after configuration. The GSCC version is 5.21.31.35; The data service board is N1PEG8;   Alarm Information NULL Handling Process 1,Creat the service firstly and then change the port attribute to Hybrid secondly, the service will be ok. 2,If the problem has happened, we should change the port attribute

zara

zara

 

E1s total affectation if services capacity exceed the bandwidth configured in RTN910

Issue Description In the RTN 910 V1R1 Huawei engineer configured 16 CES services with the U2000 Web LCT V100R002C01SPC003 correctly and began to connect tributaries one by one in the DDF. First BTSs were working normally but after engineer connect the E1 in 14 port, services in all ports got interrupted. Alarm Information CES_LOSPKT_EXC Handling Process To solve the problem it is necessary to set a modulation and a IF bandwidth according with the capacity to be configure

zara

zara

Sign in to follow this  
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.